Microbial Test 2448 Dip Slides

Microbial Test 2448 Dip Slides

Pack Size:  
Microbial Incubator 24:  
Our Price:  £10.85(Inc. 20% VAT)(£9.04 Exc. VAT)
+

Brand:  Hydra

  • Gives reliable and accurate result
  • Detects bacteria, mould and fungus growth
  • Suitable for all fuels types

Features & Advantages

  • Ensures Ongoing Fuel Quality
  • Eliminates Costly Repairs and Downtime
  • Fast, Safe and Easy to Use, Low Cost Test
  • Precise and Reliable Evaluation of Total Microbial Count
  • Dual Action - Separate Evaluation of Bacteria, Yeasts and Moulds
  • Suitable for Diesel, Marine Diesel, Biodiesel, Kerosene & Heating Oil
  • Results in 24 - 48 hours
How To Use
  1. Using a clean container take sample of fuel or water (if available) to be tested.
  2. Unscrew the lid of the container and remove the slide without touching the agar surfaces.
  3. Dip the slide into sample for 10 seconds, both sides of the dip slide must be fully wetted.
  4. Allow any excess liquid to drain for a few seconds and place slide back into tube, seal firmly.
  5. For high viscosity liquids, do not dip slide into liquid, instead use a sterile swab to take the sample, which is then streaked out onto both of the agar surfaces. Streak out evenly as a very thin layer onto the agar layers
  6. Place the slide back in the tube and screw on the top
  7. Either incubate at 30°C or place upright into dark warm place i.e. airing cupboard.
  8. After incubation for 24-48 hours at 27-30 °C, the Bacteria result is available.
  9. For slow-growing microorganisms, the result should be checked again after 48 hours.
  10. After an incubation period of 72 hours yeasts and moulds starts developing.
  11. After incubation, with the evaluation chart compare the colony density on the agar surface.
  12. With the help of tube sealed the results should be evaluated. Ideally, the incubation temperature should be as close as possible to practical conditions.
  13. Compare the results of any colony growth on the slide with the density on the evaluation growth charts.
  14. To dispose of used dip slide tubes, simply fill tube with household bleach. Re-insert the slide and dispose with normal rubbish.
  15. If test is positive, re-test within 7-10 days to check that Hydra FuelPlus Biocide treatment has dealt with problem.
 

Interpretation of results

The evaluation graph reflects the various colonies which shows the different range of microbial contamination.

The figures are shown in cfu*/ml.

  1. The colony growth of the incubated samples on the either side of the slide is compared to the images in the evaluation graph.
  2. As a test result, take an image that almost matches the colony density on the agar slide.
  3. Mainly red colonies are formed by most of the bacteria and some may form colourless colonies too. In total count colourless colonies should also be counted.

If any growth whatsoever is found you should treat your fuel immediately with Hydra FuelPlus Biocide.

Fuel-Comparison-Chart-Bacteria Fuel-Comparison-Chart-Yeast-Mould

Storage and stability

The Test Kit 2448 Dip Slide tubes should be kept away from sunlight and drought and stored safe, unopened at room temperature (about + 20 °C) .

The slides should be protected from freezing. On the box or the pack the expiration date is mentioned. Any slide displaying microbial development ought to be dumped. Heat variations might lead to condensation which eventually settles at the bottom of the dip slide tube.

This Sterile liquid can easily be discarded down the sink. This does not affects the performance and the results of Dip Slides, as the media are not visually dehydrated.

Be the first to Write a Review for this item!


Customers who bought this item also bought: